Other grades of this product :
| Potassium ferrocyanide trihyrate Basic information |
| Potassium ferrocyanide trihyrate Chemical Properties |
| Melting point | 70 °C(lit.) | | density | 1.85 | | storage temp. | Store at +5°C to +30°C. | | solubility | H2O: 0.5 M at 20 °C, clear, yellow | | form | fine crystals | | color | Yellow | | Specific Gravity | 1.85 | | Odor | Odorless | | PH Range | 8 - 10 at 211 g/l at 25 °C | | PH | 9.5 (100g/l, H2O, 20℃)(anhydrous substance) | | Water Solubility | 270 g/L (12 ºC) | | Merck | 14,7631 | | Exposure limits | ACGIH: TWA 1 mg/m3NIOSH: IDLH 25 mg/m3; TWA 1 mg/m3 | | Stability: | Stable. Incompatible with oxidizing agents, stong acids (may generate very toxic HCN). Not combustible. | | CAS DataBase Reference | 14459-95-1(CAS DataBase Reference) |
| Hazard Codes | Xn | | Risk Statements | 32-20/21/22-52/53 | | Safety Statements | 22-24/25-36-61-47 | | RIDADR | 1588 | | WGK Germany | 2 | | RTECS | LJ9219000 | | F | 8 | | TSCA | Yes | | HS Code | 28372000 | | Toxicity | LD50 orally in Rabbit: 3613 mg/kg |
| Potassium ferrocyanide trihyrate Usage And Synthesis |
| Chemical Properties | pale yellow solid | | Uses | Applied in formation of a xerogel via a cyanogel the gel has potential use in solid-state gas sensors.1 | | Uses | Moderately strong oxidizer when coupled with ferricyanide. | | Uses | Potassium ferrocyanide is a yellow crystal also known as
yellow prussiate of potash. It was made by stirring hot potassium
carbonate with wool or horn clippings with an iron rod.
It is soluble in water 1:4 but not in alcohol. Potassium ferrocyanide
was used as a developer for some iron processes and
as an additive for alkaline pyro developers. | | Preparation | Potassium hexacyanoferrate(II), K4Fe(CN)6·3H20, is obtained commercially from gasworks
spent oxide (which contains Prussian blue) by treatment with lime and subsequent
treatment of the solution with a soluble potassium salt ; the less soluble potassium hexacyanoferrate(II) can be crystallized from this mixture. In the laboratory it is readily
prepared by treating aqueous iron(II) sulphate with an excess of potassium cyanide ; the
initially precipitated iron(II) cyanide dissolves upon boiling in the excess of potassium
cyanide solution and the ferrocyanide crystallizes on cooling.
| | General Description | Potassium hexacyanoferrate(II) trihydrate, commonly known as potassium ferrocyanide, is a commonly used anticaking agent. Its cytotoxic and genotoxic effect has been evaluated. The growth of chemical garden in aqueous potassium hexacyanoferrate solution droplets on a superhydrophobic surface has been reported. The inhibition efficiency of potassium ferrocyanide in phosphoric acid solution against the corrosion of mild steel has been investigated. | | Purification Methods | The anhydrous salt is prepared by drying at 110o over P2O5 in a vacuum desiccator. To obtain the trihydrate, it is necessary to equilibrate the salt in a desiccator over a saturated aqueous solution of sucrose and NaCl. It can also be precipitated from a saturated solution at 0o by adding an equal volume of cold 95% EtOH, setting aside for several hours, then centrifuge and wash with cold 95% EtOH. It is finally sucked air dry with water-pump vacuum. The anhydrous salt is obtained by drying the hydrate in a platinum boat at 90o in a slow stream of N2 [Loftfield & Swift J Am Chem Soc 60 3083 1938]. | | Structure and conformation | The trihydrate is diamagnetic
and dimorphic existing in monoclinic (pseudotetragonal) and tetragonal forms. Its infrared spectrum in solution shows a single ν(C≡ N) at 2044 cm-1, but in the solid state a large
number of bands are observed160; ν(Fe-C) occurs at 416cm-1. White, anhydrous
K4Fe(CN)6 is obtained by dehydrating the trihydrate at 100°. |
| Potassium ferrocyanide trihyrate Preparation Products And Raw materials |
|
日本语
한국어
Français
Deutsch
España
Türkiye